1. During transportation and storage, the conveyor belt shall be kept clean and free from direct sunlight, rain and snow, and contact with acid, alkali, oil, organic solvent and other substances affecting the rubber quality, and 1 meter away from the heating device.

2、 贮存时库房内温度宜保持在—15℃—+40℃之间，相对湿度宜保持在50—80%之间。

2. During storage, the temperature in the warehouse should be kept between - 15 ℃ - + 40 ℃, and the relative humidity should be kept between 50-80%.

3、 贮存中输送带须成卷放置，不得折叠，放置期间应每季翻动一次。

3. During storage, the conveyor belt shall be placed in rolls and shall not be folded. During storage, it shall be turned once a season.

4、 输送带运行速度不应大于5.0米/秒，运输块度大，磨损性大的物料和使用固定犁型卸料装置时应尽量采用低速。超出规定速度时，会影响胶带使用寿命。

4. The running speed of the conveyor belt shall not be greater than 5.0 M / s, and the low speed shall be adopted as far as possible when transporting the materials with large block size and high abrasiveness and when using the fixed plough type unloading device. Exceeding the specified speed will affect the service life of the tape.

5、 运输机的传动滚筒直径与输送带布层的关系，传动滚筒改向滚筒的配套以及对托辊槽角的要求，应根据输 送机的设计规定，合理选取。

5. The relationship between the diameter of the driving drum and the belt layer, the matching of the driving drum and the requirements of the idler groove angle should be reasonably selected according to the design provisions of the conveyor.

6、 为减轻物料对胶带的冲击与磨损，胶 带受料段应缩短托辊间距 和采取缓冲措施。为防止 刮破胶带，挡料装置刮板清扫装置和卸料装置与胶带的接触 部 分应采用硬度适宜的橡胶板，不要采用夹有布层的胶带头。

6. In order to reduce the impact and wear of materials on the belt, the distance between rollers should be shortened and buffer measures should be taken in the receiving section of the belt. In order to prevent the belt from being scratched, the rubber plate with appropriate hardness shall be used for the contact part between the scraper cleaning device and the discharging device of the material retaining device and the belt, and the belt head with cloth layer shall not be used.

7、 输送带在使用过程中应注意以下事项：

7. Attention shall be paid to the following matters during the use of conveyor belt:

A、 避免托辊被被物料覆盖，造成回转不灵，防止漏料卡于滚筒与胶带之间 ，注意活动部分的润滑，但不得油污输送带。

A. The idler shall not be covered by the material, resulting in poor rotation, preventing material leakage from being stuck between the roller and the belt, and pay attention to the lubrication of the moving part, but do not grease the conveyor belt.

B、 力求避免带负荷启动。

B. Try to avoid starting with load.

C、 胶带发生跑偏，应及时采取措施纠正。

C. In case of belt deviation, measures shall be taken to correct it in time.

D、 发现胶带局部损伤应及时修补，以免扩大。

D. In case of local damage to the tape, repair it in time to avoid expansion.

E、 避免胶带遭受机架、支柱或块状物料的阻滞，防止碰破扯裂。

E. Avoid the blocking of the belt by the frame, pillar or block material, and prevent the belt from breaking and tearing.

本文由大倾角输送带友情奉献.更多有关的知识请点击:https://www.huafengxiangsu.com 真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

This article is dedicated by the large angle conveyor belt. For more information, please click: https://www.huafengxiangsu.com  Sincere attitude. For you to provide a comprehensive service. More relevant knowledge we will continue to dedicate to you. Please look forward to