输送带由多层橡胶棉帆布（涤棉布）或涤纶帆布包覆或耐热橡胶，经高温硫化粘合而成，适用于输送热焦炭、水泥、矿渣和热铸件等，在使用期间不可避免会出现一些问题，下面来讲解几个方面。

The conveyor belt is made of multi-layer rubber cotton canvas (polyester cotton) or polyester canvas coated or heat-resistant rubber, which is vulcanized and bonded at high temperature. It is suitable for conveying hot coke, cement, slag and hot castings. Some problems will inevitably occur during use. Here are some aspects to explain.

输送带设备接头质量不够好：

The joint quality of conveyor belt equipment is not good enough:

山东输送带接头涂胶的监督是输送带设备工艺流程中重要的环节。输送带由多层橡胶棉帆布（涤棉布）或涤纶帆布包覆或耐热橡胶，经高温硫化粘合而成，适用于输送热焦炭、水泥、矿渣和热铸件等。接头的好坏直接影响运输性是否异常。

The supervision of Shandong conveyor belt joint gluing is an important link in the process of conveyor belt equipment. The conveyor belt is made of multi-layer rubber cotton canvas (polyester cotton) or polyester canvas or heat-resistant rubber, which is vulcanized and bonded at high temperature. It is suitable for conveying hot coke, cement, slag and hot castings. The quality of the joint directly affects whether the transportability is abnormal.

硫化接头质量问题导致的皮带断裂事故频发，不仅影响生产，还造成人身伤害。接头的质量体现在使用的后果上。如果在粘接过程中不加强临时控制，仅通过竣工验收很难看出问题。因此，在输送带设备的生产过程中，严格控制硫化接头的质量是很重要的。

Belt breakage accidents caused by vulcanization joint quality problems occur frequently, which not only affect production, but also cause personal injury. The quality of joints is reflected in the consequences of use. If the temporary control is not strengthened during the bonding process, it is difficult to see the problem only through the completion acceptance. Therefore, it is very important to strictly control the quality of vulcanized joints in the production process of conveyor belt equipment.

输送带设备的长度不合适：

Improper length of conveyor belt equipment:

无论是新带设备还是旧带交换，如果当时整条输送带的设备规划不正确，精心规划，很容易造成传送带要加长。结果是配重（重锤式配重）撞到地面，导致起步打滑。确实当时没有问题，试驾也没有问题，只是设备处于低位。运行两三个月后，启动时配重下垂并着地。这是因为在设备过程中没有考虑输送带的塑性变形和弹性变形。

Whether it is new belt equipment or old belt exchange, if the equipment planning of the whole conveyor belt is incorrect and carefully planned, it is easy to cause the conveyor belt to be lengthened. As a result, the counterweight (heavy hammer type counterweight) hit the ground, resulting in starting skid. There was really no problem at the time, there was no problem with the test drive, but the equipment was low. After twoorthree months of operation, the counterweight sags and lands on the ground during startup. This is because the plastic deformation and elastic deformation of the conveyor belt are not considered in the equipment process.

此外山东输送带设备实现后无需调试调整，新设备在未磨合时，输送带容易出现偏磨损。应特别注意漏斗调料板、裙板、挡板等的调整，防止输送带跑偏、卡死等现象。另外，要加强对输送带运行过程的监控，防止输送带因大块物料的堵塞而造成适当磨损。

In addition, there is no need for commissioning and adjustment after the realization of Shandong conveyor belt equipment. When the new equipment is not run in, the conveyor belt is prone to partial wear. Special attention shall be paid to the adjustment of hopper seasoning plate, skirt, baffle, etc. to prevent the conveyor belt from deviation, jamming, etc. In addition, it is necessary to strengthen the monitoring of the running process of the conveyor belt to prevent the conveyor belt from being properly worn due to the blockage of large materials.

输送带接头质量以及长度不合适的解决便是给大家介绍的问题内容，我们希望我们的介绍可以帮助您更好地工作，可以来关注我们的网站www.huafengxiangsu.com查看更多问题的解决方法。

The solution to the problem of improper joint quality and length of conveyor belt is the content introduced to you. We hope our introduction can help you work better. You can pay attention to our website www.huafengxiangsu Com for more solutions to problems.