How to reduce the damage to conveyor belt caused by different positions? There will be a conveyor manufacturer's staff below to introduce them to you

　　一、调速滚桶与输送带损坏：反转滚桶坐落于皮带输送机尾端，输送带随反转滚桶一起转动，使下输送带变成上输送带开展原材料运输。

　　1、 Speed control barrel and conveyor belt are damaged: the reverse barrel is located at the end of the belt conveyor, and the conveyor belt rotates with the reverse barrel, so that the lower conveyor belt becomes the upper conveyor belt for raw material transportation.

　　1、在调速鼓表层周边安裝刮板板。刮料板与刮料板总体电焊焊接。刮料板用地脚螺栓固定不动在输送架上，刮料板与滚桶歪斜一定视角，以提升刮料工作能力。

　　1. Install scraper around the surface of speed regulating drum. The scraping plate and the scraping plate are welded by electric welding. The scraper plate is fixed on the conveying frame with the anchor bolt, and the scraper plate and the barrel are tilted at a certain angle to improve the scraping capacity.

　　2、在反转鼓前侧安裝V型给矿机（用地脚螺栓与声卡机架联接），给矿机与输送带触碰端安裝硫化橡胶条，降低传动带损坏。

　　2. V-type feeder is installed at the front side of the reverse drum (connected with the sound card rack by the anchor bolt), and vulcanized rubber strip is installed at the contact end of the feeder and the conveyor belt to reduce the damage of the drive belt.

　　3、除此之外，为处理反转鼓前无支撑点段溢料的难题，也可在无支撑点段安裝隔板，以降低溢料。

　　3. In addition, in order to deal with the problem of overflow in the unsupported section before the reverse drum, a baffle plate can also be installed in the unsupported section to reduce the overflow.

　　二、传动带方向跑偏导致的部分损坏：输送带方向跑偏是输送带常见问题，主要是输送带运作时，输送带轴线偏移输送带竖向轴线。能够采用维护保养对策

　　2、 Partial damage caused by the direction deviation of the transmission belt: the direction deviation of the conveyor belt is a common problem of the conveyor belt, mainly because the axis of the conveyor belt deviates from the vertical axis of the conveyor belt during the operation of the conveyor belt. Able to adopt Maintenance Countermeasures

　　1、首尾鼓不平行面，出現跑紧跑不软状况假如全部皮带输送机的轴线有误差，则必须再次校正轴线；假如只能轻度误差，则能够扭紧带座轴承。但这类方式 只有调节较小的偏移。针对很大的偏移，可将尾鼓安裝在挪动小轿车上（见下面的图），并可调节小轿车以改正误差。

　　1. The uneven running surface of the head and tail drum, in case of tight running and soft running, if the axis of all belt conveyors has errors, the axis must be corrected again; if only slight errors can be made, the bearing of the belt seat can be tightened. But this kind of way only adjusts the small offset. For a large offset, the tail drum can be installed on the mobile car (see the figure below), and the car can be adjusted to correct the error.

　　2、因为输送带自身弯折弯曲或连接头有误，造成输送带负荷不匀称，导致方向跑偏。输送带应激光切割、再次黏合或钉牢。

　　2. Because the conveyor belt itself is bent or the connector is wrong, the load of the conveyor belt is uneven, resulting in the direction deviation. The conveyor belt shall be laser cut, re bonded or nailed.

　　3、缓冲托辊组线与输送带轴线不竖直，导致输送带运作后不往前运作，即输送带向后运作（与输送带方位反过来）。假如调节方式 是偏移哪一侧，则哪一侧的缓冲托辊将偏移输送带正确方向24度，一般状况下，应调节好多个缓冲托辊以改正误差。

　　3. The central line of the buffer idler group is not vertical to the axis of the conveyor belt, resulting in the conveyor belt does not move forward after operation, that is, the conveyor belt operates backward (opposite to the direction of the conveyor belt). If the adjustment method is to offset which side, the buffer idler on which side will offset the correct direction of the conveyor belt by 2 to 4 degrees. In general, many buffer idlers should be adjusted to correct the error.

　　三、惰轮和输送带中间的损坏：能够采用维护保养对策

　　3、 Damage between idler and conveyor belt: able to adopt maintenance measures

　　1、，保证全部皮带输送机处在轴线上；次之，两边歪斜缓冲托辊与正中间水准缓冲托辊具备同样的歪斜视角。全部正中间缓冲托辊均在同一水准表面，使全部缓冲托辊与输送带触碰优良，以确保各缓冲托辊支承匀称。

　　1. First of all, ensure that all the belt conveyors are on the axis; second, the skew buffer idlers on both sides and the level buffer idlers in the middle have the same skew angle of view. All the intermediate buffer idlers are on the same level surface, so that all the buffer idlers touch the conveyor belt well, so as to ensure the uniform support of each buffer idlers.

　　2、尽量避免应用调心辊。

　　2. Try to avoid the application of the centering roller.

　　3、提升缓冲托辊的平时维护保养，立即拆换毁坏的缓冲托辊。

　　3. Lift the buffer idler for routine maintenance, and immediately replace the damaged buffer idler.